Skip to content
EndsemNov 20242024 patternFE

Engineering Graphics (EG) SPPU Endsem Question Paper Nov 2024 (paper 2)

All 10 questions from this SPPU endsem paper, as printed. Read them here or open the PDF.

Open the PDFMost repeated EG questions
Pattern
2024 pattern
Exam
Endsem
Session
Nov 2024
Max. marks
70
Time
3 Hours
Semester
I
Paper code
[6351]-116

Printed for: F.E.

Instructions to the candidates

  1. Attempt Q.1 or Q.2, Q.3 or Q.4, Q.5 or Q.6, Q.7 or Q.8, Q.9 or Q.10.
  2. Figures to the right indicate full marks.
  3. State clearly the assumptions made, if any.
  4. Use of non-programmable calculator is allowed.
  5. Assume suitable data, if necessary.

Questions

  1. Q1

    1. This part has equations that don’t show as text. Open the PDF to read it.

      [12]

  2. Q2

    1. The point P of line PQ is in HP while its other end Q is 50 mm above HP and 20 mm in front of VP. The line is inclined to VP at an angle of 40º. Draw the projections of line if its front view measures 78 mm. Find true length of line and the inclination made by the line with HP.

      [12]

  3. Q3

    1. A rhombus ABCD with diagonal AC =100 mm and BD =60 mm is resting on corner A in the Horizontal plane. Its corner B is 25 mm above Horizontal plane. Draw the projections of the plane, when top view of diagonal AC is inclined at an angle of 30 o with the vertical plane.

      [12]

  4. Q4

    1. A hexagonal plate of 35 mm side is resting on one of its corner on the HP. Draw projections of the plate when the plate surface makes an angle of 35 o to HP and the diagonal passing through resting corner makes 22 o inclination to VP. P.T.O. SPPU QUESTION PAPER www.mysppu.in Page 1 MySPPU · Engineering Graphics Page 1 of 4 2

      [12]

  5. Q5

    1. a)

      This part has equations that don’t show as text. Open the PDF to read it.

      [7]
    2. b)

      Draw the development of lateral surface of the square pyramid of base edge 40 mm and axis height 75 mm, if one of the base diagonal is parallel to VP.

      Also asked:Feb 2026 ·Apr 2025 ·Nov 2023

      [7]

  6. Q6

    1. a)

      Construct a parabola by rectangle method, if base is 80 mm and the axis height is 120 mm.

      [7]
    2. b)

      Draw the development of lateral Surface of pentagonal prism of base edge 30 mm and axis height 70 mm, if one of the base edge is parallel to VP.

      Also asked:Feb 2026 ·Apr 2025 ·Nov 2023

      [7]

  7. Q7

    1. Fig. Shows a pictorial view of an object. Using first angle method of projection draw:

      Also asked:Feb 2026 ·Apr 2025 ·Nov 2023

      [16]
    2. a)

      Front View in the derection of X

      [5]
    3. b)

      Top View

      [5]
    4. c)

      Left Hand Side View

      Also asked:Feb 2026 ·May 2025 ·Apr 2025 ·Nov 2023

      [5]
    5. d)

      This part has equations that don’t show as text. Open the PDF to read it.

      [1]

  8. Q8

    1. Fig. Shows a pictorial view of an object. Using first angle method of projection draw:

      Also asked:Feb 2026 ·Apr 2025 ·Nov 2023

      [16]
    2. a)

      Sectional Front View about its symmetry in the direction of X

      Also asked:Feb 2026 ·May 2025 ·Nov 2023 ·May 2023

      [5]
    3. b)

      Top View

      [5]
    4. c)

      Left Hand Side View

      Also asked:Feb 2026 ·May 2025 ·Apr 2025 ·Nov 2023

      [5]
    5. d)

      Give Dimensions

      [1]

  9. Q9

    1. Isometric Projection-Figure shows front view and top view of an object. Draw isometric view and show overall dimensions. OR SPPU QUESTION PAPER www.mysppu.in Page 3 MySPPU · Engineering Graphics Page 3 of 4 4

      [16]

  10. Q10

    1. Figure shows front view and side view of an object. Draw isometric view and show overall dimensions. eeee SPPU QUESTION PAPER www.mysppu.in Page 4 MySPPU · Engineering Graphics Page 4 of 4

      [16]