Skip to content
EndsemApr 20252024 patternFE

Engineering Graphics (EG) SPPU Endsem Question Paper Apr 2025

All 10 questions from this SPPU endsem paper, as printed. Read them here or open the PDF.

Open the PDFMost repeated EG questions
Pattern
2024 pattern
Exam
Endsem
Session
Apr 2025
Max. marks
70
Time
3 Hours
Semester
I/II
Paper code
[6401]-2406

Printed for: F.E.

Instructions to the candidates

  1. Attempt Q.2 or Q.3, Q.4 or Q.5, Q.6 or Q.7, Q.8 or Q.9 or Q.10.
  2. Figures to the right indicate full marks.
  3. State clearly the assumptions made, if any.
  4. Use of non-programmable calculator is allowed.
  5. Assume suitable data, if necessary.

Questions

  1. Q1

    1. The end point P of line PQ is 25 mm above HP while its point Q is 15 mm in front of VP. Its plan and elevation makes 40° and 35° with XY respectively. Draw the projection, if the projector distance between the end points is 60 mm. Find inclination made by the line with HP and VP.

      Also asked:Feb 2026

      [12]

  2. Q2

    1. This part has equations that don’t show as text. Open the PDF to read it.

      [12]

  3. Q3

    1. An equilateral triangle of 60 mm side is resting on HPon one of its side. Then its surface is inclined with HP at an angle of 40°. Draw the projections of plane, if the resting side is inclined to VP at an angle of 30°.

      [12]

  4. Q4

    1. A pentagonal plane of side 40 mm is resting on HP on its corner and the edge opposite to the corner makes an angle of 25° with VP. Surface of the plane, is inclined at 40° to HP. Draw the projections of the plane. P.T.O. SPPU QUESTION PAPER www.mysppu.in Page 1 MySPPU · Engineering Graphics Page 1 of 4

      [12]

  5. Q5

    1. a)

      Draw the ellipse by focus directrix method if the distance from focus to directrix is 60 mm and the eccentricity ratio is 2/3.

      Also asked:Feb 2026 ·May 2024 ·Nov 2023

      [7]
    2. b)

      Draw the development of lateral surfaces of pentagonal prism of base side 30 mm and axis height 80 mm.

      Also asked:Feb 2026 ·Nov 2024 ·Nov 2023

      [7]

  6. Q6

    1. a)

      Draw the involute of circle of diameter 50mm.

      [7]
    2. b)

      Draw the development of lateral surface of cone of base diameter 50 mm and axis height 70 mm.

      Also asked:Feb 2026

      [7]

  7. Q7

    1. Fig. shows a pictorial view of an object. Using first angle method of projection draw:

      Also asked:Feb 2026 ·Nov 2024 ·Nov 2023

      [16]
    2. a)

      Front View

      [5]
    3. b)

      Top View

      [5]
    4. c)

      Right Hand Side View

      Also asked:Feb 2026 ·May 2025 ·Nov 2024 ·Nov 2023

      [5]
    5. d)

      Give Dimensions OR SPPU QUESTION PAPER www.mysppu.in Page 2 MySPPU · Engineering Graphics Page 2 of 4

      [1]

  8. Q8

    1. Fig. shows a pictorial view of an object. Using first angle method of projection draw:

      Also asked:Feb 2026 ·Nov 2024 ·Nov 2023

      [16]
    2. a)

      Front View

      [5]
    3. b)

      Top View

      [5]
    4. c)

      Right Hand Side View

      Also asked:Feb 2026 ·May 2025 ·Nov 2024 ·Nov 2023

      [5]
    5. d)

      Give Dimensions

      [1]

  9. Q9

    1. Figure show orthographic views of an object by first angle method of projection. Draw its isometric view. OR SPPU QUESTION PAPER www.mysppu.in Page 3 MySPPU · Engineering Graphics Page 3 of 4

      [16]

  10. Q10

    1. Figure show orthographic views of an object by first angle method of projection. Draw its isometric view.  SPPU QUESTION PAPER www.mysppu.in Page 4 MySPPU · Engineering Graphics Page 4 of 4

      [16]